Physical Facility Tour

The Seaton Hardware Testing Lab

Where theory meets 415V power distribution, high-CFM airflow tunnels, and component-level electronics diagnostics.

Seaton, Gippsland VIC

Engineered for Real Load & Thermal Stress

Our dedicated educational workshop facility in Gippsland, Victoria is purpose-built to simulate real-world thermal challenges, electrical loads, and diagnostic troubleshooting without risk to production environments.

Rather than relying on theoretical software models, our testing facility runs live 415V three-phase supplies, high-volume variable speed ducted plenums, and high-frequency ASIC hardware rigs under controlled ambient conditions.

Testing laboratory electrical distribution and diagnostic instruments
Testing Stations

Specialized Diagnostic & Calibration Benches

High-Voltage Power Distribution & Metering Bench

Hands-on industrial switchboard featuring 32A three-phase drops, heavy-gauge C19/C20 power distribution units, and transient surge suppression.

Dedicated Apparatus:
  • • Fluke 435 Series II Three-Phase Power Quality Analyzer
  • • Type C and Type D thermal-magnetic circuit breaker test rack
  • • True-RMS digital clamp multimeters and earth-loop impedance testers
  • • Live harmonic distortion (THD) oscilloscope monitoring displays
Learning Purpose: Enables students to safely practice conductor sizing, breaker selection, neutral load balancing, and continuous current derating on live industrial circuits.

Thermal Aerodynamics & Static Pressure Test Chamber

A modular wind-tunnel enclosure equipped with variable-speed axial fans, static pressure sensors, and thermal imaging cameras.

Dedicated Apparatus:
  • • FLIR E8-XT High-Resolution Infrared Thermal Camera
  • • Dwyer 475 Series Digital Manometers for static pressure differential logging
  • • Hot-wire thermo-anemometers for measuring duct air velocity (FPM / CFM)
  • • Acoustic sound level meter (Type 1 precision) for dBA baffle benchmarking
Learning Purpose: Demonstrates the physical impact of restricted intake louvres, dirty filter media, and duct bends on hashboard temperatures and fan RPM.

Micro-Electronics & SMD Hashboard Rework Station

Six individual technician workstations configured for component-level fault isolation, signal tracing, and hot-air soldering.

Dedicated Apparatus:
  • • High-definition trinocular stereomicroscopes with LED ring illumination
  • • Quick 861DW ESD-safe 1000W lead-free hot air rework stations
  • • Hakko FX-888D precision temperature-controlled soldering irons
  • • Rigol DS1054Z four-channel digital storage oscilloscopes
  • • Antminer and Whatsminer automated serial test fixtures
Learning Purpose: Allows participants to probe CLK, RST, and TX test points, isolate shorted voltage domains, and practice chip replacement on real silicon.

Firmware & Pool Telemetry Calibration Rig

Dedicated network test bed with isolated managed switches, Stratum proxy servers, and automated power monitoring sockets.

Dedicated Apparatus:
  • • Braiins OS+ & VNISH enterprise tuning firmware deployment servers
  • • Shelly & Sonoff industrial power telemetry smart relays
  • • Grafana real-time Prometheus dashboard showing per-chip core thermals
  • • Failover pool routing simulation and packet loss test harnesses
Learning Purpose: Hands-on autotuning labs where students undervolt live hashboards and lock in rock-solid J/TH power efficiency profiles.

Facility Safety Protocols & Standards

Because our lab operates high-amperage 415V electrical lines and high-temperature micro-soldering apparatus, rigorous safety protocols are embedded into every session:

✓ AS/NZS 3000 Australian electrical code compliance strictly enforced
✓ Full personal protective equipment (PPE) supplied to every attendee
✓ Emergency remote shunt-trip power disconnects at every bench
✓ Fume extraction hoods on all micro-soldering and flux stations
✓ Low student-to-instructor ratio (max 8 per cohort) ensuring constant supervision

Experience Real Hardware Diagnostics in Person

Join our next scheduled workshop cohort or arrange an individual technical session at 23 Hill Road, Seaton.

Reserve Lab Placement